Asosiy parametr

1) Ultra-thin:two layer 3D protect non woven,surface layer(each one line inside and outside）,touch composite non woven,ADL,up tissue(or non woven）,SAP sheet,down tissue(or non woven）,bottom film,bottom film composite non woven,Pattern tape,discard tape,leg spandex(3 plus 3),waistband inside non woven,waistband outside non woven,waistband spandex(19 plus 23）

2)Cotton type:two layer 3D protect non woven,surface layer(each one line inside and outside）,touch composite non woven,ADL,up tissue(or non woven）,pulp plus SAP,down tissue(or non woven）,bottom film,bottom film composite non woven,Pattern tape,discard tape,leg spandex(3 plus 3),waistband inside non woven,waistband outside non woven,waistband spandex(19 plus 23）

1. Mahsulot hajmi:

XXL: to'liq uzunlik 530mmX440mmX paxta yadrosi 400mmX bel 405mm

XL to'liq uzunlik: 510mmx 440mmx paxta yadrosi400mmx bel chizig'i405mm

L: to'liq uzunlik: 480mmx410mmx paxta yadrosi370mmx bel 405mm

M: to'liq uzunlik: 450mmx 410mmx paxta yadrosi370mmx bel 405mm

S: to'liq uzunlik: 420 mm x 390 mm x paxta yadrosi 370 mm x bel 405 mm

Hajmi mijoz tomonidan hal qilinishi mumkin, bizning mashinamiz mijozning talabiga binoan loyihalashtiriladi.

2. Quvvat: 350 KVt

3. Mashinaning og'irligi: 95 T

4. Ta'minot: 380V 50HZ

5. Mashina o'lchami: 42m7.5m3.5m

6. Air :0.6-0.8Mpa,6000L/min（buyer need prepare the air compressor)

7. Mashina rangi: sut oqi

8. Mashinada ishlaydigan yon qoplamali nikel

Asosiy konfiguratsiya

1.Reasonable kvadrat po'latdan yasalgan mashina ramkasi.

30 mm qalinlikdagi devor taxtasi oltita{1}}qirrali frezalash mashinasiga moslashtiriladi.

Ramka 50 mm50 mm qattiq kvadrat po'latdan mos keladi.

Devor taxtasi vintni perchinlashni moslashtiradi, u payvandlashdan ko'ra barqarorroq bo'ladi, samolyot hammasi perchinlashni moslashtiradi.

To'shak ramkasi 100mm100mm8mm kvadrat po'latdan mos keladi.

Orqaga haydash 1100 mm gacha kengayadi, uni saqlash osonroq bo'ladi, chunki katta joy.

Ba'zi materiallar tashqi ochish moslamasini oziqlantirish materialini 90 darajaga moslashtiradi.

Mashinada yopishtiruvchi mashinalarni topish uchun ikkinchi qavat mavjud. Bu joyni tejashga yordam beradi.

2. Maydalagich tizimi

Pulpa tokchasi bilan jihozlang, vositadan foydalaning, pulpani ko'taring, pulpaning maksimal diametri 1400 mm dan kam yoki unga teng.

Use best Chinese brand crusher "minghai",30KW,can crush untreated pulp,semi-treated pulp and treated pulp,can crusher max width 500mm,the pulp bursting strength Less than or equal to 1300kpa ,crusher Greater than or equal to 500kg/h.

Pulpa moslashtirilgan servo motor boshqaruvi, pulpa oziqlantirish tezligi asosiy mashina avtomatik bilan mos keladi, pulpa ishlatilganda mashina avtomatik ravishda to'xtatilishi mumkin.